• CSCD核心中文核心科技核心
  • RCCSE(A+)公路运输高质量期刊T1
  • Ei CompendexScopusWJCI
  • EBSCOPж(AJ)JST
二维码

隧道建设（中英文） ›› 2025, Vol. 45 ›› Issue (4): 687-694.DOI: 10.3973/j.issn.2096-4498.2025.04.003

• 研究与探索 • 上一篇    下一篇

基于图像三维重建的变截面隧道超欠挖检测方法及应用

阳军生1， 罗钰博1， 傅金阳1，*， 陈建伟1， 万正2， 祝志恒3   

  1. （1. 中南大学土木工程学院， 湖南 长沙 410083； 2. 贵州省公路工程集团有限公司， 贵州 贵阳 550008； 3. 广东交科检测有限公司， 广东 广州 510550）
  • 出版日期:2025-04-20 发布日期:2025-04-20
  • 作者简介:阳军生(1969—)，男，湖南永兴人，1996年毕业于中南工业大学，土木工程专业，博士，教授，主要从事隧道及地下工程科研与教学工作。E-mail: jsyang@csu.edu.cn。*通信作者： 傅金阳， E-mail: jyfu2010@163.com。

Over- and Under-Excavation Detection Method and Application of Variable-Section Tunnels Based on Three-Dimensional Image Reconstruction Technology

YANG Junsheng1, LUO Yubo1, FU Jinyang1, *, CHEN Jianwei1, WAN Zheng2, ZHU Zhiheng3   

  1. (1. School of Civil Engineering, Central South University, Changsha 410083, Hunan, China; 2. Guizhou Highway Engineering Group Co., Ltd., Guiyang 550008, Guizhou, China; 3. Guangdong Jiaoke Detection Co., Ltd., Guangzhou 510550, Guangdong, China)
  • Online:2025-04-20 Published:2025-04-20

PDF

42

摘要： 为解决现有超欠挖快速检测方法不能有效适应变截面隧道的问题，提出一种基于图像三维重建技术的变截面大断面隧道超欠挖检测方法。该方法以变截面隧道轴线作为流线、以设计开挖断面作为迹线，通过截面放大系数k表征隧道变截面的特征，构建适用于变截面隧道的曲面计算方程，形成变截面隧道设计开挖轮廓计算算法。依托花江峡谷大桥六枝岸隧道式锚碇工程，布置控制点并采集现场照片，基于图像三维重建技术对隧道锚实际开挖变截面轮廓进行点云重建与三维曲面重建，采用网格射线法对比实际开挖和设计变截面轮廓，计算超欠挖； 以现场实际喷射混凝土量与全站仪测量结果作为参考指标，对变截面超欠挖检测方法的准确性进行验证。研究结果表明： 该方法能够实现对变截面隧道各开挖循环超欠挖的快速、准确检测，检测结果平均相对偏差率仅1.50%，偏差率低于传统检测方法(2.83%)。该方法提升了隧道超欠挖检测方法的适用范围，现场应用效果良好，可为变截面隧道开挖质量控制提供可靠依据。

关键词: 隧道锚, 变截面隧道, 图像三维重建, 超欠挖检测

Abstract: The existing over- and under-excavation detection methods cannot effectively adapt to variable tunnel sections. To address this issue, an over- and under-excavation detection method based on three-dimensional image reconstruction technology is proposed for variable large cross-sectional tunnels. The tunnel axis serves as the streamline, and the designed excavation cross-section acts as the reference line. The variable-section characteristics of the tunnel are represented by a section enlargement factor k, which is used to construct a surface calculation equation suitable for such tunnels and to form a calculation algorithm for the designed excavation contour. The proposed method was applied to the Liuzhi-side tunnel anchorage project of the Huajiang Canyon bridge. The control points are established, and field photographs are collected. The actual excavation contours of the variable-section tunnel anchorage are reconstructed as point clouds and three-dimensional (3D) surfaces using 3D image reconstruction technology. The grid-ray method is then employed to compare the actual excavation with the designed variable section profiles, enabling the calculation of the over- and under-excavation. The accuracy of the proposed method is validated by comparing its results with actual sprayed concrete volumes and total station measurements. The results demonstrate that the proposed method enables rapid and accurate detection of over- and under-excavation for each excavation cycle in the variable-section tunnels. The average relative deviation rate of the detection results is only 1.50%, which is significantly lower than that of traditional methods (2.83%). The proposed method expands the applicability of over- and under-excavation detection techniques, demonstrates excellent performance in field applications, and provides a reliable basis for quality control during the excavation of variable-section tunnels.

Key words: tunnel anchorages, variable-section tunnel, three-dimensional image reconstruction, over- , and under-excavation detection

主办单位：中铁隧道勘察设计研究院有限公司    主管单位：中铁隧道局集团有限公司

本系统由北京玛格泰克科技发展有限公司设计开发 技术支持：support@magtech.com.cn

粤ICP备19038941号